Installation Instructions
Ford Van (Full Size)
All models incl. Vans with
Factory Step Bumper**
Does Not Fit Pre-1992 E-350 or 124”
Wheelbase Models
Part Numbers:
44027
51007
Hitch Shown In Proper Position
Equipment Required:
Wrenches: 3/4, 7/8
Drill Bits: 1/2”
Carbon Canister
if equipped
1
1992 and Later Models – see Figure 1 & 2 Modification of vehicle exhaust may be necessary on vehicle with twin tip exhaust.
**Note: 1992 and later vehicles with factory step bumpers required 12” long ball mount or weight distributing shank.
Note: Wiring harness is located inside vehicle frame. Reposition prior to drilling
1. If present, lower carbon canister from driver’s side frame rail.
2. Lower spare tire. Note: Relocation of under vehicle spare tire is no required. Tire may have to be repositioned slightly forward to avoid contact
with receiver tube.
3. Remove all but a thin layer of undercoating from attaching surfaces.
4. Disconnect factory installed optional driver’s side trailer wiring connector from bumper.
5. Position receiver on vehicle as shown, lining up with existing holes in frame.
6. Loosely install bolts, blocks (depending on model: see Figures 1 & 2), flat washers, conical washers and nuts.
7. Using receiver as a template, drill a 1/2” hole is each frame rail and install 1/2” bolts, block (depending on model), conical washers and nuts.
Note:
if existing hole is present, forward slot may be used in place of drilled hole.
8. Reinstall factory trailer wiring connector to clear receiver.
9. Raise spare tire while positioning tire forward on vehicle. Check for clearance between differential and bracket lines.
10. Reattach carbon canister if present – carbon canister must not contact bolt head. If it does loosen canister fasteners and reposition the
canister to ensure clearance with bolt head.
Tighten all 1/2-13 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Rev. A6-27-06N51007Sheet 1 of 2
z2001, 2002, 2006 Cequent Towing Products
Hex nut 1/2-13Qty. (6)
5
Flat Washer 1/2 (Large)Qty. (2)
9
Conical Washer 1/2Qty. (6)
4
Flat Washer 1/2 (Small)Qty. (2)
8
Block .25 X 1.50 X 2.00Qty. (4)
3
Block .25 X 1 X 2Qty. (2)
7
Block .25 X 1.50 X 2.00Qty. (2)
2
Hex Bolt 1/2-13 X 1.75Qty. (4)
6
Carriage Bolt 1/2-13 X 1.75Qty. (2)
1
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
Fastener Kit: 51007-051
Do Not Exceed Lower of Towing Vehicle
Manufacturer’s Rating or
500 (227 Kg)5000 (2270 Kg)
Weight Carrying
Ball Mount
1000 (454 Kg)10,000 (4540 Kg)
Weight Distributing
Max Tongue
WT (LB)
Max Gross
Trailer WT (LB)
Hitch type
Wiring Access Location: SUV1, SUV2
2
3
5
4
3
7
6
6
8
9
Crossmember
Hole to be drilled in vehicle frame,
each side. Be
careful not to drill into
Carbon canister
Existing hole in frame
* Depending on vehicle configuration,
forward hole may line up with existing
hole in frame – use same fastener
combination
Figure 1.
1992 and later E-350 & E-250 Models
Bumper
*
SERIES 51®
Fasteners typical both sides
Form: F205 Rev A 5-6-05
(3 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern