PRO-SERIES 800388 Bedienerhandbuch PDF herunterladen

Manual Addendum – Insert this into your Scaffold Assembly and Operating Instructions Manual

200803 Manual Addendum

The maximum distributed load capacity decreases with the number of sections that are used. The total combined weight of

workers, material, and equipment must not exceed the rated working load.

Maximum Load Capacity Base Section - 1,000 Lbs (Workers & Materials) 2 Sections - 850 Lbs (Workers & Materials)

Install side braces, platform and guard rail at desired height. All four L-shaped lock pins must be inserted fully in holes on

frame. WARNING: Be certain the Pin is fully inserted into hole (Figure 1). Do not leave the Pin half-inserted (Figure 2).

Figure 1

Pin Is NOT Fully Engaged

Pin Is Fully Engaged (Locked)

Figure 2

Whenever units are stacked, outriggers are required. Do not use a utility scaffold over 1 frame high without outriggers. Failure

to use outriggers will make scaffold more likely to tip over, causing serious injury or death. You must install outriggers before

stacking the second scaffold unit.

Outriggers (GSORSET) and Guard Rail (GSGRS) are required when stacking. Maximum stack is 2 with GSORSET.

Guard rail must be installed so that gate swings inward over platform. Failure to install guard rail properly may result in serious

injury or death.

When accessing platform, climb over the top of end frame ladder – DO NOT SWING AROUND SIDE OF END FRAME.

Swinging around side of end frame will cause scaffold to tip over, resulting in serious injury or death.

For Stacking An Additional Unit, Follow These Instructions:

1. Erect the base unit first.

2. Install the casters into all 4 outriggers and secure each with lock pin. Set the caster brake on each.

3. Outrigger should be installed on each leg of the scaffold. Clamp the outrigger to the frame at 90° angle to the side brace.

Tighten clamp securely. Clamp must be flush against scaffold leg, and casters must be in contact with the surface.

4. Add second scaffold level by stacking the end frame over on top of the base unit end frame.

5. Install side braces, platform and guard rail at desired height. All four L-shaped lock pins must be inserted fully in holes

on frame. Be certain the Pin is fully inserted into hole (Figure 1). Do not leave the Pin half-inserted (Figure 2).

6. Add guard rail. NOTE: The guard rail does not fit on the frame! Install

the guard rail in the sockets on the side brace. (Figure 3).

Figure 2

Figure 1

Figure 3

Pin Is Fully Engaged (Locked)

Pin Is NOT Fully Engaged

1 2 3 4 5 6 7 8 9

200803 Manual Addendum 1

Inhaltsverzeichnis

Seite 1 - 200803 Manual Addendum

Manual Addendum – Insert this into your Scaffold Assembly and Operating Instructions Manual 200803 Manual Addendum The maximum distributed load capa

Seite 2

Post these scaffolding safety guidelines in a place where it will be seen and understood by all persons who erect, dismantle or use scaffolding. Be c

Seite 3

readily fit together and the resulting scaffold’s structural integrity is maintained by the user. L. Planking – 1. Worki

Seite 4

Apéndice del manual – Inserte esta hoja en el Manual de instrucciones de montaje y uso del andamio Apéndice del manual 200803 La capacidad de carga

Seite 5

Coloque estas indicaciones de seguridad en un lugar en que puedan ser vistas y entendidas por todas las personas que participen en el montaje, desmont

Seite 6

H. DEBE PROVEERSE EL ACCESO A TODAS LAS PLATAFORMAS. No se trepe sobre refuerzos cruzados o diagonales. I. SUMINISTRE UN SISTEMA DE VALLAS DE SEGURI

Seite 7

Addenda au Manuel – Insérez le présent document au Manuel de montage et d’utilisation de votre échafaudage 200803 Addenda au Manuel La capacité de c

Seite 8

Afficher ces consignes de sécurité relatives aux échafaudages dans un endroit où elles seront vues et comprises par toutes les personnes qui montent,

Seite 9

Lorsque les échafaudages sont pleinement ou partiellement confinés, ou lorsqu’ils sont sujets à des charges de basculage, des attaches supplémentaires

Kommentare zu diesen Handbüchern

Keine Kommentare

PRO-SERIES 800388 Bedienerhandbuch

Stöbern Sie online oder laden Sie Bedienerhandbuch nach Nein PRO-SERIES 800388 herunter. PRO-SERIES 800388 Instructions / Assembly Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Nein PRO-SERIES 800388